pmip3:design:6k:index
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
pmip3:design:6k:index [2009/02/05 20:04] – pasb | pmip3:design:6k:index [2009/12/23 14:23] – Closed the discussion jypeter | ||
---|---|---|---|
Line 1: | Line 1: | ||
~~ODT~~ | ~~ODT~~ | ||
- | ~~DISCUSSION~~ | + | ~~DISCUSSION:closed~~ |
- | //Go to =>// [ [[pmip3: | + | < |
- | ====== 6ka Experimental Design ====== | + | //Go to =>// [ [[pmip3: |
+ | ====== 6ka Experimental Design ====== | ||
+ | |||
+ | <note warning> | ||
===== Boundary conditions ===== | ===== Boundary conditions ===== | ||
- | **Summary of 6ka boundary conditions | + | ==== Summary of 6ka boundary conditions |
- | ^ ^ | + | |
- | | Orbital parameters | + | ^ ^ PMIP3/ |
- | | | + | | Orbital parameters |
- | | Trace Gazes | + | | |
- | | Aerosols | + | | Trace gases |
+ | | Aerosols | ||
| | | | | | | | | | ||
- | | Solar constant | 1365W/m2 | As in PI | | + | | Solar constant |
- | | Vegetation | + | | Vegetation |
- | | Ice sheet | + | | Ice sheets |
- | | Topography and coastline | + | | Topography and coastlines |
- | ** Vegetation | + | *For the ice-sheet reconstruction, |
- | Depending on the complexity of the model used the vegetation will be either | + | |
- | - computed by the model | + | |
- | - prescribed to PI | + | |
- | - prescribed to 6ka vegetation reconstructed from a combination of model output and data analyses (please use the map provided here) | + | |
+ | Please use the [[index# | ||
- | ===== Initial conditions ===== | ||
- | ^ ^ PMIP3 ^ Alternative solution ^ | + | ==== Vegetation ==== |
- | | Initial conditions | branch off PI after adjustement | Same as in PI | | + | |
- | | Model spin up | Same as in PI | | + | The vegetation should be treated |
+ | |||
+ | | ||
+ | * Prescribed to PI with interactive LAI (models with interactive carbone cycle, but no vegetation dynamics) | ||
+ | * Computed by the model (models with dynamic vegetation) | ||
+ | |||
+ | There are still questions concerning the possibility to have a 6ka reconstructed vegetation from a combination of model output and data analyses that could be used for sensitivity experiments. Please tell if you are interested by such a map and what would be the best variables (pft?) that should be provided (see comment from B. Otto-Bliesner in the discussion pannel). | ||
+ | |||
+ | ==== For Earth System Models with interactive carbone cycle ==== | ||
+ | |||
+ | The simulations are forced by CO2 concentrations. Please use the same protocol | ||
+ | |||
+ | ==== Insolation ==== | ||
+ | |||
+ | Note that insolation should follows PMIP requirements. Please check it carefully using the following tables ([[http:// | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | ===== Initial conditions ===== | ||
+ | ^ ^ PMIP3 ^ Alternative solution | ||
+ | | Initial conditions | Branch off PI after adjustement | ||
+ | | Model spin up | Same as in PI | | | ||
Line 41: | Line 64: | ||
[ [[pmip3: | [ [[pmip3: | ||
[ [[pmip3: | [ [[pmip3: | ||
- | [ [[wiki: | + | [ [[wiki: |
pmip3/design/6k/index.txt · Last modified: 2010/09/16 14:35 by jypeter