Differences

This shows you the differences between two versions of the page.

--- pmip3:design:6k:index [2009/02/05 20:04] – pasb
+++ pmip3:design:6k:index [2010/09/16 14:35] (current) – Added link to final BC page in the top warning jypeter
@@ Line 1: / Line 1: @@
 ~~ODT~~
-~~DISCUSSION~~
+~~DISCUSSION:closed~~
-//Go to =>// [ [[pmip3:design:pi:index|PI]] ] - [ [[pmip3:design:21k:index|21ka]] ] - [ [[pmip3:design:lm:index|LM]] ]
+<html><a name="page_top_tag">&nbsp</a></html>
-====== 6ka Experimental Design ======
+//Go to =>// [ [[pmip3:design:pi:index|PI]] ] - [ **6ka** ] - [ [[pmip3:design:21k:index|21ka]] ] - [ [[pmip3:design:lm:index|LM]] ] - [ [[pmip3:design:8k2:index|8.2ka]] ] - [ [[pmip3:design:li:index|LI]] ] - [ [[pmip3:design:plio:index|Plio]] ]
+====== 6ka Experimental Design ======
+<note warning>This was a BC //development page// (see [[index#page_bottom_tag|discussion]] panel at the end of the page)\\ \\ Make sure you use the [[pmip3:design:6k:final|final version of the 6k BC]]!</note>
 ===== Boundary conditions =====
-**Summary of 6ka boundary conditions **
+==== Summary of 6ka boundary conditions ====
-^      ^   PMIP3  ^  Alternative solution ^
-|  Orbital parameters  |  ecc= , obl=  , peri=  | |
+^      ^   PMIP3/CMIP5  ^  Minimum solution  ^
-|  date of the Vernal equinox | March 21 at Noon | |
+|  Orbital parameters  |  [ **ecc** = 0.018682 ] - [ **obl** = 24.105° ] - [ **peri-180°** = 0.87° ]  |  |
-|  Trace Gazes  |  | |
+|  Date of vernal equinox  |  March 21 at noon  | |
-|  Aerosols     | Same as in PI  | |
+|  Trace gases  |  [ **CO<sub>2</sub>** = 280 ppm ] - [ **CH<sub>4</sub>** = 650 ppb ] - [ **N<sub>2</sub>O** = 270 ppb ] - [ **CFC** = 0 ] - [ **O<sub>3</sub>** = same as PI ]  | |
+|  Aerosols  |  Same as PI  | |
 |    | |  |
-|  Solar constant | 1365W/m2 |  As in PI |
+|  Solar constant  |  1365 W/m<sup>2</sup>  |  As in PI  |
-|  Vegetation     | Interactive  |  See specific note below |
+|  Vegetation     |  prescribed or interactive as in CMIP5 PI  |    |
-|  Ice sheet      | remnant Laurentide ice-sheet (provided) | Same as in PI |
+|  Ice sheets      |  Remnant Laurentide ice-sheet (provided*)  |  Same as PI  |
-|  Topography and coastline | Modification of the Hudson Bay (provided) | Same as in PI  |
+|  Topography and coastlines  |  Modification of Hudson Bay coastlines (provided*)  |  Same as PI  |
-** Vegetation  **
+*For the ice-sheet reconstruction, see discussion on LGM wiki page
-Depending on the complexity of the model used the vegetation will be either
-- computed by the model
-- prescribed to PI
-- prescribed to 6ka vegetation reconstructed from a combination of model output and data analyses (please use the map provided here)
+Please use the [[index#page_bottom_tag|discussion]] panel to **comment** this table!
-===== Initial conditions =====
-^  ^ PMIP3 ^ Alternative solution ^
+==== Vegetation ====
-| Initial conditions |  branch off PI after adjustement | Same as in PI |
-| Model spin up      |  Same as in PI |  |
+The vegetation should be treated as in the CMIP5 PI experiment. The reason is that in CMIP5 we test the version of the model used for future climate projections. Since OA and ESM models will be considered, depending on the model used the vegetation will be
+  * prescribed to PI (which means both vegetation types and LAI are prescribed )
+  * Prescribed to PI with interactive LAI (models with interactive carbone cycle, but no vegetation dynamics)
+  * Computed by the model (models with dynamic vegetation)
+There are still questions concerning the possibility to have a 6ka reconstructed vegetation from a combination of model output and data analyses that could be used for sensitivity experiments. Please tell if you are interested by such a map and what would be the best variables (pft?) that should be provided (see comment from B. Otto-Bliesner in the discussion pannel).
+==== For Earth System Models with interactive carbone cycle ====
+The simulations are forced by CO2 concentrations. Please use the same protocol as in CMIP5 to store the carbone fluxes and the variables needed for PCMIP (see list here)
+==== Insolation ====
+Note that insolation should follows PMIP requirements. Please check it carefully using the following tables ([[http://pmip2.lsce.ipsl.fr/design/tables/inso_tables_6k.shtml|6ka BP insolation tables]])
+===== Initial conditions =====
+^  ^  PMIP3  ^  Alternative solution  ^
+| Initial conditions |  Branch off PI after adjustement  |  Same as in PI  |
+| Model spin up      |  Same as in PI  |  |
@@ Line 41: / Line 64: @@
 [ [[pmip3:|PMIP3 Wiki Home]] ] -
 [ [[pmip3:wiki_help|Help!]] ] -
-[ [[wiki:syntax|Wiki syntax]] ]
+[ [[wiki:syntax|Wiki syntax]] ] <html><a name="page_bottom_tag">&nbsp</a></html> - [ [[index#page_top_tag|Top]] ]